Shingles
Class 4 impact-rated shingles
Laminated shingles that carry a Class 4 rating in the UL 2218 impact test. That's a rating for the product, not a promise about any storm. Available on new roofs.
Ridge
Ridge vent and cap
The ridge cap seals the peak and lets the attic breathe.
Flashing
Step flashing
A bent piece of metal at every row where the roof meets the chimney. Joints are where a lot of leaks begin.
Flashing
Valley flashing
Metal down the valley, where two slopes meet and the most water runs.
Underlayment
Synthetic underlayment
A second line of defense. If a shingle ever fails, this is what keeps water out of your attic.
Underlayment
Ice and water shield
A sticky membrane along the eaves and in the valleys, where water backs up first.
Deck
Roof deck
The boards the whole roof is nailed to. If a board is soft or rotted, we photograph it and replace that board.
Frame
Rafters
We check them from the attic for soft or wet wood before anyone mentions a price.
Flashing
Drip edge
Metal at the roof's edge that steers water into the gutter, not behind it.
A roof you can stop thinking about.
Leak repair, storm repair and new roofs for homes within about 30 miles of the shop. You see a photo of every problem before you hear a price.
A 3D model of a house roof, cut away on one side to show its layers. Rain and hail hit one half of the roof and bounce off. The other half sits in warm, low sunlight.
Parts of the roof shown in the model:
- Class 4 impact-rated shingles: laminated shingles with a Class 4 rating in the UL 2218 impact test. A rating for the product, not a promise about any storm. Available on new roofs.
- Ridge vent and cap: seals the peak and lets the attic breathe.
- Step flashing: bent metal at every row where the roof meets the chimney.
- Valley flashing: metal down the valley, where two slopes meet.
- Synthetic underlayment: the second line of defense under the shingles.
- Ice and water shield: a sticky membrane along the eaves and in the valleys.
- Roof deck: the boards the whole roof is nailed to.
- Rafters: the frame, checked from the attic for soft or wet wood.
- Drip edge: metal at the roof's edge that steers water into the gutter.
Let's take it apart. Then put it back the right way.
The model's shingles, flashing, underlayment and deck lift off until only the rafters are left.
01 / Frame
First we look. Then we talk.
Every job starts with a free inspection. We climb up, go into the attic, and check the rafters for soft or wet wood before anyone mentions a price.
The roof stripped down to the bare wooden rafters.
02 / Deck
A solid base under everything.
The deck is the plywood the whole roof is nailed to. If a board is soft or rotted, we photograph it and replace that board. We don't cover it up.
Plywood decking going on over the rafters.
03 / Underlayment
The layer you never see.
Underlayment rolls out over the deck as a second line of defense. If a shingle ever fails, this is what keeps water out of your attic.
Underlayment rolled out across the deck.
04 / Flashing
Sealing the seams.
Flashing is the metal that seals the joints around the vents, the walls and the valleys. Joints are where a lot of leaks begin, so this is where we slow down.
Metal flashing set around the vents, the walls and the valleys.
05 / Shingles
Shingles, laid to shed rain.
Each row overlaps the one below, so water runs down and off. Every shingle is nailed where the maker says it should be.
Charcoal shingles laid row by row from the bottom edge up.
06 / Ridge
Capped. Checked. Your turn.
The ridge cap seals the peak and lets the attic breathe. Then we walk you through the photos. Want the same look at your roof? It's free.
The ridge cap goes on and the roof is finished. The storm rolls back over it.